• Resolved an issue where the TMS would not run due to an upgrade to Postgres 16.

Grid Configurator

• [Cybersecurity Enhancement] Updated PostgreSQL to version 16.4.
• Addressed an issue in versions 6.0.0.30 and 6.1.0.18 where 48 hours after the software was installed it could no longer communicate with devices.

SEL-451-6 Settings Driver

• Updated SEL-451-6 Z107:
  • Added OFF to the range of the HIFLLRT setting.

SEL-487E-5 Settings Driver

• Added support for SEL-487E-5 Z206:
  • Added second-harmonic blocking logic for all current terminals.
  • Added the IEC 61850-9-2LE Sampled Values (SV) publication capability. This option includes support for the INT2, INT4, INTD, INT7, and INT8 I/O interface boards.
  • Added support for the INTD I/O interface board for TiDL and SV subscriber models.
  • Added the High-Availability Seamless Redundancy (HSR) protocol feature.
  • Added Group setting ALTVm (where m = S, T, U, W, X, Y) to allow dynamic voltage source selection for each current terminal.
  • Increased the number of available remote bits to 96.
  • Modified software to allow different CT ratios for combined terminal applications.
  • Added Port 5 setting BUSMODE for TiDL models to allow merged mode when using the five-port Ethernet card.
• Addressed an issue in the SEL-487E-5 Z202–Z204 versions where the TAPS–TAPX settings, if calculated automatically, were indicated as being in error when the corresponding TAPMAX/TAPMIN ratio was less than 35.

• Updated to support Blueframe OS version 1.10 and later.
• Enhanced the handling of link states when devices are connected through a traditional switch.
• Improved flow table management to keep all the flows for the same circuit in the same flow table.
• Improved host discovery performance.

acSELerator QuickSet SEL-5030, QuickSet Common Files, QuickSet Prerequisites

• Addressed an issue with QuickSet not being able to automatically reconnect to a device after sending Port Settings to the device over an FTP connection.
• Corrected an issue where copying or moving settings between RDB files in the Database Manager could fail.

QuickSet Bay Control Screens

• Added SEL-411L screens 200-201.
• Added SEL-451-5 screen 1039.
• Updated SEL-487E screen LV126.
• Added SEL-487E screens HV169-172, TRI49-52, and LV129-132.
• Added SEL-487V screen 528.

SEL-351 QuickSet Settings Driver, SEL-351A QuickSet Settings Driver, SEL-351S QuickSet Settings Driver 

• Corrected an issue with the a0 setting value being loaded incorrectly when opening saved settings if the KGN setting value was not set to OFF.

SEL-400G QuickSet Settings Driver 

• Addressed an issue with the SEL-400G Z001-Z006 Device Part Number form label text being cut off.

SEL-451 QuickSet Settings Driver 

• Updated support for SEL-451-5 Z032:
  • Added OFF to the range of the HIFLLRT setting.

SEL-487E QuickSet Settings Driver 

• Addressed an issue with the SEL-487E-3, -4 Z108-Z115 Device Part Number form label text being cut off.

SEL-T401L QuickSet Settings Driver 

• Added support for SEL-T401L Z004:
  • Added the HSZ setting to allow the use of voltage traveling waves for double-ended, traveling-wave-based fault locating and line monitoring.
  • Added Relay Word bits 59An, 59Bn, and 59Cn (n = 1-2) to indicate an instantaneous overvoltage condition on a per-phase basis.
  • Added the ability to remotely upgrade relay firmware over an Ethernet network.

SEL-787 QuickSet Settings Driver 

• Addressed an issue that prevented the SEL-787-4 Z006 Maximum-to-minimum TAP ratio error message from showing when the Maximum-to-minimum Tap ratio was ≤32.00.

SEL-2414 QuickSet Settings Driver 

• Addressed an issue with SEL-2414 Z100 having Display Point Settings disabled when the device has a Large Display Module touchscreen.

SEL-2431 QuickSet Settings Driver

• Addressed an issue with SEL-2431 Z011-Z013 where an error was displayed if IPADDR equaled the DNPIPn (n = 1-5) setting value and the Port E (Ethernet port) DNP Session was disabled.

acSELerator QuickSet SEL-5030, QuickSet Common Files, QuickSet Prerequisites

• Renewed the digital signature certificate.

acSELerator Database

• [Cybersecurity Enhancement] Updated PostgreSQL to version 16.4.

acSELerator Database Device Manager Support, acSELerator Database Legacy Driver Support

• No changes. The new version is compatible with acSELerator Database version 4.0.0.x.

QuickSet Device Manager Plugin

• [Cybersecurity Enhancement] Updated to use Python version 3.12.6.

QuickSet Team Plugin

• Updated to work with PostgresSQL version 16.4.

QuickSet Bay Control Screens

• Added SEL-451-5 screen 1038.

SEL-700G QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added support for new device driver SEL-700G Z009:
  • Added part number support pertaining to the new LEA card on Slots E and Z.
  • Added new Group settings pertaining to the new LEA card.
  • Added new Global settings pertaining to the new LEA card.
  • Added new Relay Word bits and updated usage rules.

SEL-700BT QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added support for new device driver SEL-700BT Z003:
  • Added part number support pertaining to the new LEA card on Slots E and Z.
  • Added new Group settings pertaining to the new LEA card.
  • Added new Global settings pertaining to the new LEA card.
  • Added new Relay Word bits and updated usage rules.

SEL-710 QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added support for new device driver SEL-710-5 Z006:
  • Added part number support pertaining to the new LEA card on Slot Z.
  • Added new Group settings pertaining to the new LEA card.
  • Added new Global settings pertaining to the new LEA card.
  • Added new Relay Word bits and updated usage rules.

SEL-787 QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added DNET Protocol to Port 4 PROTO setting when Slot C is configured as OX (empty slot).
• Added support for new device driver SEL-787-4 Z006:
  • Added part number support pertaining to the new LEA card on Slots E and Z.
  • Added new Group settings pertaining to the new LEA card.
  • Added new Global settings pertaining to the new LEA card.
  • Added new Relay Word bits and updated usage rules.

SEL-787L QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added 89OC Relay Word bits and 89OC pairing capabilities to the DNP Binary Output Map.

SEL-787Z QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Added 89OC Relay Word bits and 89OC pairing capabilities to the DNP Binary Output Map.

SEL-751 QuickSet Settings Driver 

• Corrected the cropping seen with some Analog values displayed in the HMI Metering Overview.
• Removed Math Variable Analog Quantities (MV01–MV32) from the Modbus Map.

SEL-2414 QuickSet Settings Driver

• Addressed an issue where Slot 6 Output SELogic settings will be hidden when a 4 DI/3 DO card is selected for Slot Z.

acSELerator QuickSet SEL-5030, QuickSet Common Files, QuickSet Prerequisites

• [Cybersecurity Enhancement] Updated to remove dependency on unsupported Microsoft C++ runtime redistributables.

acSELerator Database

• [Cybersecurity Enhancement] Updated to remove dependency on unsupported Microsoft C++ runtime redistributables.

acSELerator Database Device Manager Support

• Addressed an issue that prevented the SEL-411L-A, SEL-411L-B, and SEL-451-A DEFAULT_GENERATE_PASSWORD scripts from running.

acSELerator Database Legacy Driver Support

• No changes. The new version is compatible with acSELerator Database version 3.1.10.x.

QuickSet Bay Control Screens

• Added SEL-411L screens 198-199.
• Added SEL-451-5 screens 1036-1037.
• Added SEL-487E screens HV168, TRI47-48, and LV128.
• Added SEL-487V screens 526-527.

• Added the CommProc Converter extension to convert legacy SEL-2020, SEL-2030, and SEL-2032 Communications Processor settings files into RTAC settings.
• Upgraded the Digital Fault Recorder extension to add generic assets, analog input channel settings, user-defined custom channels, and other new features.
• Upgraded the Simple Tag Mapper extension to add CSV map import, DNP and Modbus shared map settings integration, and live data/logging-only modes.
• Enabled usage of the CAA FB Factory library.
• Resolved an issue where pasting content into the Tag Processor caused a shift of focus to the project tree.
• Resolved an issue introduced in version 1.37.153.8000 where projects could fail to automatically restore during an upgrade of acSELerator RTAC from a previous version
• Resolved an issue introduced in version 1.37.153.8000 where projects could fail to open and would produce an error message stating "This schema should have an Automation task."
• Resolved an issue introduced in version 1.37.153.8000 where a Modbus server imported from XML would not include tags.

• [Cybersecurity Enhancement] Updated the WinSCP third-party component to maintain continuity of support.
• Added the Grid Connect extension.
• Added the DMA Link extension.
• Added the 87L Comm Monitor extension.
• Added a Tag Selector tool to allow browsing and easy selection of all tags in a project with drag-and-drop operations so that these tags can be copied into supported fields, such as the Simple Tag Mapper and Tag Processor.
• Enhanced the project tree to display the connection status of devices as offline, online, or disabled while connected to an RTAC with firmware version R151 or later installed.
• Enhanced the project tree to allow copy and paste operations for IEC 61131 User Logic elements (Programs, Functions, Function Blocks, Data Types, and GVLs) in RTAC project with a firmware version of R148 or later.
• Added an Other column to the Start Page project list that indicates the presence of the Advanced Read-In components (Ethernet Settings, HMI Projects, etc.) in a project.
• Enhanced the task re-ordering dialog to support bulk assignment for the order of items in the main and automation tasks when using a custom order.
• Added a prompt to confirm the overwrite of stored device passwords (e.g., Level 1 password for SEL Protocol client) when the settings are sent to an RTAC.
• Enhanced the speed of the acSELerator RTAC setup installer process.
• Enhanced the speed and project version compatibility when creating a new project from XML content or importing XML content into an existing project.
• Enabled usage of the CAA_Memory library.
• Added the to_string attribute to internal system enumeration types, such as quality_t and validity_t. Existing user logic that casts these types to strings may need to be revised when upgrading the project to firmware version R153 or later.
• Resolved an issue where a DNP server using an Ethernet-based connection type was not added to a project.
• Resolved an issue where an incorrect project version was displayed after creating settings from XML content.
• Resolved an issue where custom user logic using non-default access specifiers would force the settings to be resent when going online.
• Resolved an issue where a Mirrored Bits Protocol device could not be renamed if the device resided in the Automation Task.
• Resolved an issue where a change to the custom user logic did not update a project's Last Modified time stamp.
• Resolved an issue where a name used by a device and subsequently removed from the project could not be re-used.
• Resolved an issue where an IEC 61850 SCD configuration file could not be re-applied to a project if advanced read-in project items such as Ethernet settings were present.
• Resolved an issue introduced in 1.35.152.8000 where a project with a firmware version of R136 or earlier could fail to export.
• Resolved an issue where a project containing aliased tags and an extension forced a settings resend when attempting to go online.
• Resolved an issue in the Tag Processor where a Destination Tag containing a bit reference was not fully populated.
• Resolved an issue in the IEC 60870-5-101 server where a failover serial port was unable to use a baud rate of 200 or 600.
• Resolved an issue where an Axion touchscreen configured with a Bay Screen that used a name that was not IEC 61131-3-compliant caused an error.
• Resolved an issue where a project containing an Axion touchscreen device could not be exported.
• Resolved an issue where an Axion touchscreen could not be exported or imported in XML format.
• Resolved an issue where a project containing NGVLs with custom data types could encounter issues with compiling, opening, cleaning, and exporting.
• Resolved an issue where double-clicking on a function block in CFC logic no longer prompted users to select which instance of the function block to view.
• Resolved an issue where browsing a library manager could cause unnecessary Windows processes to initiate.
• Resolved an issue where debug-stepping into a method was no longer possible.

ConditionMonitoring(3.5.3.1)

• Addressed an issue in class_CmReportWriter where detail file content was misaligned relative to column labels. This occurred when multiple bootstrapped sources presented unequal numbers of detail columns.

FTPSync(3.5.2.3)

• Added "." (dot) "-" (dash) and "@" (at) as supported characters for the FTP username.
• Addressed an issue where COMTRADE events were not synchronized in RTAC firmware versions R152-V1 and later if the RTAC system time was not synchronized with the device originating the event.

FileIO(3.5.7.5)

• Added NewestFileTime output to class_DirectoryListing GetList method.

GridConnect(3.5.7.4)

• Added real and reactive power clamp functionality for storage assets.
• Added setting EnableVarForAllGroups to fb_masterPlantController to allow for assets that are not producing real power to participate in reactive power objectives.
• Modified storage assets to participate in reactive power objectives while charging.
• Modified storage assets to not participate in meeting PSetpoint objectives while StorageChargeSetpoint is greater than 0 even if the storage asset has completed charging.
• Increased fb_masterPlantController input MaxFileSize to 10 MB. The default value is now 5 MB.
• Changed the default value of fb_masterPlantController input EnableDdrRecording to TRUE.
• Resolved an issue where an asset entering reactive power clamp could cause setpoints of non-clamped assets to increase.
• Resolved an issue where changing an asset's PRating or QRating would not maintain the previous setpoint until the next evaluation period.

GridConnect(3.5.6.5)

• Resolved an issue which prevented storage assets from participating in reactive power objectives when only storage assets are present.

IPAliasRedundancy(3.5.3.3)

• Addressed an issue where a gratuitous ARP was not being transmitted when the IP alias was activated.

SELUtils(3.5.6.0)

• Added enumerations to represent enumerated states of an SEL-2488 Satellite-Synchronized Network Clock polled over SNMP.
• Added BYTES_TO_IPv4_STRING and BYTES_TO_MAC_ADDRESS_STRING to support converting byte strings to ASCII representations.
• Added FORMAT_SIGNIFICANT_FIGURES function to evaluate floating point numbers according to a specified number of significant figures.
• Added fb_TTLInput function block to evaluate analog values to interpret Boolean representations.
• Modified PID and CascadeControl function blocks to reduce the number of visible variables.

SELUtils(3.5.5.1)

• Modified fun_CheckLicense to support R200 firmware.

87L Comm Monitor(1.35.0.1)

• Library update only.

CommProc Converter(1.34.0.0)

• Initial release.

CtPt Monitor(1.33.0.5)

• Library update only.

Digital Fault Recorder(1.36.0.0)

• Added a Generic Asset Type.
• Added configuration of user-defined Custom Digital and Analog Channels to allow DFR triggering and recording from external tags.
• Added configuration for Analog Input Extended Range Modules for DFR triggering and recording.
• Added setting to enable generation of SOE Log CSV files.
• Added setting for Synchrophasor Server PDC ID and PMU Data Rate.
• Added a calculated IN neutral current value for Transmission Line and Generic assets.
• Enhanced Local Monitoring to calculate disk space usage statistics.
• Modified asset trigger configuration column names to specify units.
• Resolved an issue where a Build DFR operation would fail due to the presence of invalid settings combinations.
• Resolved an issue where assets and EtherCAT modules could be assigned invalid names.

FTP Sync(1.36.0.0)

• Added "." (dot) "-" (dash) and "@" (at) as supported characters for the FTP username.
• Resolved an issue introduced in 1.35.0.0 where CEV event monitoring would fail on an SEL Protocol device that contained _SEL in the middle of the device name.

Grid Connect(1.35.0.2)

• Resolved an issue where Multidrop Serial clients would not be allowed to share a common serial port.
• Resolved an issue where ControlMode on PCC Settings could not be set to NoControlMode.
• Resolved an issue where upgrading from extension version 1.35.0.0 to 1.35.0.1 could prevent a project from being opened.

Simple Tag Mapper(1.36.0.0)

• Added support for CSV file map imports.
• Added support for integration of DNP and Modbus shared map settings (point number, variation, etc.) on the generated map tabs.
• Added support for live data and logging-only modes to allow live data and SOE logging functionality without any tag mapping features.
• Added support for the FUNCTION operator to allow use of a custom IEC 61131 function to populate server tags.
• Addressed an issue where multiple instances of Simple Tag Mapper could not be inserted into a project.

•  [Cybersecurity Enhancement] Updated the acSELerator Database Reader application to use remote server identity information from the acSELerator Database Connection Key to enhance X.509 connection verification when connecting to the database.
• Added the ability to map assets to objects in ESRI Map using attributes other than ObjectID.
• Improved the configuration of the C37.118 Reader for UDP_S connections.
• Added the ability to save the file name in a Data Export template.
• Modified Device Events so that only trip events get the trip icon.
• Improved configuration of the Digitals.csv file so that commas are not required when all states are not labeled.
• Improved the highlighting in the cursor legend of the Time-Series Trend.
• Added the Event Store application.
• Added the DMA Receiver application.

• Updated to .Net Core 8.0.8

• [Cybersecurity Enhancement] Updated the acSELerator Database Reader application to use remote server identity information from the acSELerator Database Connection Key to enhance X.509 connection verification when connecting to the database.
• Added the ability to map assets to objects in ESRI Map using attributes other than ObjectID.
• Improved the configuration of the C37.118 Reader for UDP_S connections.
• Improved the contour layer drawing algorithm so that contours render correctly over large regions and the contour mask works correctly.
• Added the ability to save the file name in a Data Export template.
• Added a function to the Calculations application that allows the use of a primary and one or more backup signals for calculations.
• Added the ID column to the Notification Table.
• Disallowed calculation libraries with names that begin with a digit.
• Modified Device Events so that only trip events get the trip icon.
• Improved configuration of the Digitals.csv file so that commas are not required when all states are not labeled.
• Improved the precision of the ESRI Map box zoom.
• Improved the highlighting in the cursor legend of the Time-Series Trend.
• Added the Event Store application.
• Added the DMA Receiver application.

• Updated to .Net Core 8.0.8

• Updated to .Net Core 8.0.8

SEL-5052 version 4.5.0.1 is compatible with both versions 4.5.0.0 and 4.5.0.1 of SEL-5051. Includes all the functions of SEL-5052 version 4.5.0.0 with the following additions:

• Resolved an issue in the SEL-5052 Installer that prevented a user from upgrading SEL-5052 to version 4.5.0.0 if the software had been originally installed by a different user.
• Resolved an issue that, in redundant NMS Server operation, sometimes prevented the SEL-5052 Installer from upgrading the Standby SEL-5052 due to a communication failure with the Primary.
• Reverted a change introduced in version 4.5.0.0 that prevented SEL-5052 from sending automated alarm notification emails to some SMTP servers. Added logging that identifies related local configuration issues.

All Operational Modes

• Identical to version 4.5.0.0. The version number is incremented to coincide with a corresponding SEL-5052 release.

• [Cybersecurity Enhancement] Updated the installer to use a secure temporary directory. This update addresses a vulnerability in the installer that could allow someone to execute arbitrary code with the privileges of a user uninstalling the application.
• Architect Edition 2.1 Schema Enhancements:
  • Architect now displays the release attribute of an IED in the Properties tab.  The release attribute is applicable to Edition 2.1 (ClassFileVersion 010 and newer) devices.
  • Improved the third party SCT subscription configuration for Edition 2.1 (ClassFileVersion 010 and newer) IEDs by setting the noIctBinding ClientServices attribute to true.
  • Architect will save the SCD file using the SCL version 2007, revision B, release 4 if there is an IED in the project with an original SCL version/revision/release of 2007B1 (Edition 2.1) or later.
• Added the following features to enable indexed reports functionality for server IEDs that support it:
  • For IEDs that support indexed reports, the maximum number of instances can now be set for each report (RptEnabled element's max value).
  • Architect will now display the number of instances that a report consumes when an SEL IED supports indexing.
  • When reports are indexed, the range of possible indexed values is now displayed in the name column.
  • The instance names of a report's preconfigured reservations are now viewable when editing the report.
  • The Reports tab now displays the count of the buffered and unbuffered report instances out of the maximum supported for Edition 2.1 devices.
• Various other enhancements:
  • SEL IED internal databindings are now maintained using sAddrs instead of esel:datasrc. 
  • Converted the esel:datasrc databidings to sAddr in the DataTypeTemplate for ClassFileVersion 010 and newer devices.
  • Updated the IED Upgrade Tool so that it will upgrade the databindings to the appropriate format for the IED ClassFileVersion.
  • Architect now creates the default names of Reports in a range from NewReport -> NewReportZZ.
  • ConfRev can now be set to 0 for GOOSE or SV publications without a defined/referenced dataset.
  • Resolved an issue where Architect would incorrectly set the indexed value to true when it should have been false when creating a new report publication in an Edition 1 IED.
  • Resolved an issue where the Reports tab would not load and displayed an error when the maximum number of reports was exceeded.
  • Resolved an issue where valid Edition 1 ICD files could not be imported and were treated as schema-invalid.
  • Resolved an issue where the installer did not uninstall the SCL toolkit when installing Architect via SEL Compass.
  • Resolved an issue where the APPID field was too restrictive and did not allow for Type 1A GOOSE transmissions.
  • Resolved an issue where there could be a loss of supervision logical nodes when the IED Upgrade Tool is used to upgrade an IED with an ICD file where the first logical device has a different inst.
  • Resolved an issue where invalid datasets would not appear in the upgrade report after an IED was upgraded with the IED Upgrade Tool.
  • Resolved an issue that prevented adding or removing more than one client input selection at a time in the Client Inputs tab.
  • Resolved an issue that caused the first client input on the list to be added or removed when the IED name was double-clicked to open the dropdown in the Client Inputs tab.
  • Enhanced Architect interoperability with third party tools by updating the indexed value to false for ReportControl elements when editing a project file containing Edition 1 and Edition 2 SEL IEDs.
  • Resolved an issue that prevented a user from renaming an IED when adding the IED to the project.
  • Resolved an issue where the Deploy CIDs tool would not move past a device it could not connect to when deploying CID files to multiple devices.
  • Resolved an issue where the Semantic compare tool would compare two files with the same name and not show any differences.
  • Resolved an issue where an improperly formatted cbRef in a supervision logical node would cause the same error to appear twice in the output window.

• Improved performance in Diagram Builder for extremely large projects.
• Improved RTAC Connections to allow for special characters in passwords.
• Miscellaneous bug fixes.

• [Cybersecurity Enhancement] Updated third-party components to ensure continuity of support.

• [Cybersecurity Enhancement] Updated the uninstaller to control access to the uninstall directory.
• [Cybersecurity Enhancement] Updated third-party components to ensure continuity of support.
• Enhanced notification to the user when their mySEL account is inactive when installing or updating packages.

• [Cybersecurity Enhancement] Updated third-party components to ensure continuity of support.

• Added support for folder type operations.

• Updated the synchroWAVe Event application installer so that all dependencies are included. Previously, synchroWAVe Event did not include dependencies in its install package and instead downloaded the required .NET packages from Microsoft’s website.
• Reduced the time required to parse custom calculations.
• Added support in the Bewley Diagram for the new SEL- TWFL Dual Traveling-Wave Fault Locator.
• Added parser support for converting CEV and COMTRADE files to a format useable by the SEL-5401 Relay Test System software for use with the SEL-AMS Adaptive Multichannel Source.
• Updated the following library dependencies: SciChart from v7.0.2 to v8.3.0, .NET from v6.0 to v8.0, and Protobuf from v3.24.4 to v3.25.3.
• Corrected an issue where sequence components were not calculated when there was a duplicate signal name across multiple files.

• [Cybersecurity] Updated the installer to protect against maliciously place files.
• [Cybersecurity Enhancement] Enabled additional compiler features to help prevent the execution of malicious code.
• Updated a third-party driver for better Windows 10 and 11 compatibility.

• [Cybersecurity] Improved validation of project files to protect against malicious content in .ldmz and .ldme files.

• Improved audit support for layer-two-only hosts.
• Improved support for audits with traditional switches in the network.
• Filtered audits for TCP Port 0.

• Added subgroup capability to views.
• Added option to configure number of significant figures for Numeric Display.
• Added minimum y-axis scale option for Standard Chart.
• Added option to configure signal line thickness on Standard Chart.
• Increased web client data export limit.

• Updated to support Blueframe OS version 1.10 and later.
• Enhanced the handling of link states when devices are connected through a traditional switch.
• Improved flow table management to keep all the flows for the same circuit in the same flow table.
• Improved host discovery performance.

• [Cybersecurity] Resolved an issue where an authenticated user attempting to change their password could do so without using the current password.
• [Cybersecurity] Resolved a cross-site scripting issue that was only accessible by valid authenticated users.
• The System Name setting in the System Settings application now always displays on the header bar.
• Added a new account permission to allow access to network diagnostic utilities.
• Network diagnostic utility queries are now recorded in Blueframe's system logs.
• Resolved an issue where 503 Service Unavailable responses were returned when attempting to access data or open applications.
• Resolved an issue where the X.509 certificate could not be deleted.
• Resolved an issue where pages would not load or the user was incorrectly redirected to the login page when attempting to navigate the Blueframe UI.
• Resolved an issue where some syslog messages did not contain the data from the AppID field in the system logs application.
• Resolved an issue where a backup node in a redundancy configuration incorrectly reports an inconsistent disk state.
• Resolved an issue where a primary node in a redundancy configuration incorrectly reported a loss of communications to backup nodes with an "incompatible firmware" message.
• Resolved an issue where backups could not be restored.
• Resolved an issue where IRIG-B synchronization status was shown incorrectly.
• Resolved an issue where Blueframe web services could not be accessed through port forwarding or network address translation. Each individual application will need to be updated to support this functionality. Check the release notes for desired applications.

• Resolved an issue where data points were not viewable.

• Resource Management functionality:
  • Addressed an issue in TERMINALGATEWAY connection children where settings were always shown as changed.
  • Addressed an issue that prevented the assignment of connections to templated session instances.

• Resource Management functionality:
  • Resolved an issue that could result in duplicate attribute names being present when changing resource presets.
  • Resolved an issue where resources may remain in the side detail view after being deleted.
  • Resolved an issue that prevented export selection of certain combinations of parent-child devices.
  • Resolved an issue that prevented edits to child device gateway parameters.
  • Resolved an issue that locked the increment/decrement controls of the delay time values on the COMPROC protocol.
  • Resolved an issue that prevented the modification of child device credential used in parent-child connections (this issue did not impact COMPROC parent-child connections).
  • Resolved an issue that prevented the addition of a gateway child to a COMPROC connection.
  • Resolved an issue where a restricted user could be presented with an exception error when a resource access list referenced an unknown device.
  • Resolved an issue that incorrectly marked instance credential labels as duplicates in the Create Credentials features of Profiles.
  • Resolved an issue that caused the show/hide empty folders button in Resource Selection to have no effect.
  • Resolved an issue that prevented BRE and ACC level assignments in Sessions.
  • Resolved an issue that reverted some session template settings to default after editing and saving.
  • Resolved an issue that prevented exporting when a folder and subfolder were both selected.
  • Updated invalid parameter references to now display the reason why they are invalid within their dropdown rows.
  • Updated to allow existing device credentials to be used when a child device is added to a parent connection rather than automatically creating a new credential template every time.
  • Added support for Access Level C on SEL communication processors.
  • Added specific access level support for the SEL-734B and SEL-734W.
  • Added the ability to save changes during profile deployment.
  • Added Parent Folder context to the Create Folder dialog.
  • Added a progress indicator for profile actions.
  • Added support for allow/denylist and access level settings in Profile Sessions templates with per-instance connection configurations.
  • Added the ability to apply a single value to an entire column in a grid in Profile Instance Credentials.
• Notifications functionality:
  • Added the ability to reset all data.

• General functionality:
  • Resolved an issue that incorrectly scaled collected LDP values.
  • Resolved an issue where publications were falsely flagged as having new data to publish.

• General functionality:
  • Added support for COMTRADE reports that include a nanosecond resolution in the .cfg file.
  • Enhanced handling of plans and publications for large scale systems.
• Direct Resource Access functionality:
  • Added the ability to write to the Blueframe System Log for commands sent from a QuickSet connection through a Direct Resource Access Session.

• Credential Management functionality:
  • Resolved an issue where the filter would not apply in the Select Resources dialog.
  • Resolved an issue that caused duplicate labels in the Exceptions dialog when a device had a parent with the same credential label.
  • Added the ability for the SELFTP Level 2/2AC credential to be updated when a resource has the Level 2 credentials updated by a Direct Password Rotation plan.
  • Added support for Resource Management Saved Filters in the Plan and Report resource selection.
  • Added consistency across DMA configuration applications such that the Enable Plan field now contains only the start date and start time.
• Credential Monitoring Archive functionality:
  • Enhanced the Password Audit report to include a Rotated On time stamp for each access level or username.
  • Changed the CSV report to match the columns available in the archive report view.

• Credential Management functionality:
  • Addressed intermittent application load failures due to heavy system burden.
  • Resolved an issue where the 2AC password would become out of sync for an FTP connection when an SEL device is configured to have the Access Level 2 password rotated.

• Configuration Monitoring functionality:
  • Resolved an issue that made time-of-day schedule configuration inconsistent with time-zone offset variations.
  • Resolved an issue where the filter would not apply in the Select Resources dialog.
  • Added support for secure variants of FTP to be used with Publications.
  • Added support for selecting which resources to include in the Run Plan Now window.
• Configuration Monitoring Archive functionality:
  • Resolved an issue where the archived report column sorting preview showed incorrect values.

• Configuration Monitoring functionality:
  • Addressed intermittent application load failures due to heavy system burden.
  • Resolved an issue that prevented email publications from sending an email upon new data collection.
• Configuration Monitoring Archive functionality:
  • Resolved an issue that would prevent configuration difference reports on the same resource to launch.
  • Resolved an issue where the passphrase necessary for the SEL-3620 Ethernet Security Gateway configuration was not persisted.

• Custom Monitoring functionality:
  • Resolved an issue that made time-of-day schedule configuration inconsistent with time-zone offset variations.
  • Resolved an issue where the filter would not apply in the Select Resources dialog.
  • Added support for secure variants of FTP to be used with Publications.
  • Added support for selecting which resources to include in Run Plan Now window.
• Custom Monitoring Archive functionality:
  • Enhanced the reports to support resource counts up to 1000.

• Custom Monitoring functionality:
  • Addressed intermittent application load failures due to heavy system burden.
  • Resolved an issue that prevented email publications from sending an email upon new data collection.

• Disturbance Monitoring functionality:
  • Resolved an issue that made time-of-day schedule configuration inconsistent with time-zone offset variations.
  • Resolved an issue where the filter would not apply in the Select Resources dialog.
  • Added support for secure variants of FTP to be used with Publications.
  • Added support for selecting which resources to include in the Run Plan Now window.
• Disturbance Monitoring Archive functionality:
  • Resolved an issue that prevented the Message field from appearing in Disturbance Monitoring CSV reports.
  • Resolved an issue where the archived report column sorting preview showed incorrect values.

• Disturbance Monitoring functionality:
  • Addressed intermittent application load failures because of heavy system burden.
  • Resolved an issue that prevented email publications from sending an email after collecting new data.

• DMA Diagnostics functionality:
  • Resolved an issue in Live Executions that caused publication plans to show an Error in the Names and Application columns.

• DMA Diagnostics functionality:
  • Addressed intermittent application load failures due to heavy system burden.
  • Resolved an issue that prevented the Listening Log from loading when the system had a large history of available logs.

Moved the DMA REST API to be included with the DMA Tools package.

Initial version that includes support for Meter Monitoring and Meter Monitoring Archive:

• Meter Monitoring functionality:
  • Load data profiling (LDP) collection from SEL-734, SEL-735, and RTAC Trend Recorder.
  • Voltage sag, swell, and interruption (VSSI) collection from SEL-734 and SEL-735.
  • Publication support.
• Meter Monitoring Archive functionality:
  • Report summary creation.
  • Report export.

• Increased support for as many as 1000 DNP clients and as many as 500K points across all DNP clients.
• Enhanced the configuration editor to enable/disable related settings fields without saving the configuration first.
• Resolved an issue where the DNP UDP and TLS transport methods did not accept/create connections.
• Resolved an issue where some protocol services versions would not upgrade to the next version.
• Resolved an issue where when an item was copied, additional copies would be generated incorrectly.
• Resolved an issue where Ethernet multidrop did not accept multiple connections on a single port.
• Resolved an issue where the Link Status Timeout setting was not applied to the DNP client operation.
• Resolved an issue in the DNP server where per point object variant settings could not be modified.
• Resolved an issue in the create copies dialog where text could be entered in a field that was not currently selected.
• Resolved an issue where a DNP server did not accept a new client connection in a timely manner if the previous client connection did not close the socket connection with a FIN or RST tcp flag.
• Resolved an issue where a DNP client communication status would incorrectly indicate as offline if the client connection was no longer selected in the tree.
• Resolved an issue when the quality of the DNP connection status was always invalid when viewed in the Data Viewer application.
• Resolved an issue where no data would be shown on the screen after closing the SSH Public Key editor and leaving the editor blank.

• Added the Disturbance Monitoring and Configuration Monitoring Widgets

• Added a diagnostics panel for DMA data collection jobs that include RTAC assets.
• Resolved an issue where the Resource Viewer service would continuously restart.

• FLISR functionality
  • Added support to consume breakers in Substation or Distribution models.
  • Added support for switch property expansion.
  • Added the ability for FLISR to detect non-overcurrent event outages using field device voltage measurements. These types of outages are typically caused by burned jumpers, broken conductors, or a loss of substation source. This feature will include both open phase detection, loss of source detection, and voltage measurement error detection.
  • Added additional settings to support customer operational needs.
  • Enhanced FLISR to only publish FlisrAlarm for the device in the alarm.
  • Made improvements to the Return to Normal function.
  • Enhanced the FLISR algorithm for disarmed feeders.
• Report API functionality:
  • Added voltage events.

• PSM Core functionality:
  • Added keyboard hot keys
  • Added the ability to build a substation model in addition to a distribution model.
  • Added the ability for substation and distribution models to be linked.
  • Expanded switch properties to support multiple variants of switches in the field.
• Model Data Import functionality:
  • Added functionality to read substation GeoJSON models.
  • Added a new "auto" operator in node properties for Substation models.
  • Updates to API.

• [Cybersecurity Enhancement] Updated base OS to ensure continuity of support.
• Removed support for legacy boot. For devices that only support legacy boot, such as the SEL-3332, 3351, and 3354, you must use SEL BaRT version 5.0.1.1 or older.
• Changed the filename extension for new backup files from '.img' to '.bart'
• to differentiate SEL BaRT image files from other file types that use the
• '.img' extension. Existing SEL BaRT backup files that have the '.img'
• extension are still fully supported by SEL BaRT.
• Added exFAT filesystem support for the backup location. Drives formatted
• as exFAT that contain a backup_images folder can now be used as a backup file storage location.
• Added BTRFS filesystem support for Backup and Restore functions, supporting resize on Restore to fit smaller and larger destination drives.
• Added XFS filesystem support for Backup and Restore functions, no resize on Restore support (destination drive must be same size or larger).
• Improved Shrink and Restore to smaller drive functions to use significantly less free space in the backup location when shrinking the backup data.
• Added a prompt to override the Backup function free-space check. Backup file size cannot be accurately predicted, so the user is now given the option to either cancel or proceed with the backup at their discretion.
• Improved make_selbart displayed usage instructions.
• Improved make_selbart.exe to resolve some instances where the drive could not be written to because other Windows processes are accessing the drive.
• Resolved an issue where the Restore command could fail due to insufficient drive space even though the destination drive was the same size as the original drive.

• [Cybersecurity Enhancement] Updated base OS to ensure continuity of support.
• Improved Raw backup file metadata to prevent restoring the backup to drives that are too small to store the backup data.
• Improved Restore logic to correctly restore backups that contain more than 1 TB of data.

• SEL-3350

• Updated SEL-3350 firmware to improve status LED behavior at startup.
• Updated SEL-3350 contact input IN201-IN224 default pickup/dropout debounce setting values to 4ms to meet surge immunity at 24 Vdc input.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Improved time synchronization accuracy and jitter between the system clock and SEL Time Controller.
• Improved network adapter statistics reporting to support functions like the powershell command Get-NetAdapterStatistics.
• Updated the Contact Input class NominalVoltage property to return an error when attempting to set to an invalid value.
• Corrected the Contact Input class NominalVoltage property setpoints for 120/240 VAC, previously they were incorrectly labeled 125/250 VAC.
• Corrected the Contact Input class InputVoltage property to not report erroneous values when more than 32 volts is applied to the input.
• Corrected the COM port numbers assigned to SEL-3350 serial ports 22 and 23, previously the numbers were swapped.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for SEL-3350 3U serial and I/O expansion boards.
• Added SortPorts.exe utility, which sorts the COM# numbers of SEL serial ports into sequential order at startup. See Readme.txt and product manuals for details.
• Fixed an issue in the Ethernet driver that could sometimes cause a system crash during bootup.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for new SEL PCI devices, components, and variants.
• Improved Ethernet SFP behavior on hot-plug and device enable/disable.
• Updated the SEL_Time WMI class to correctly report External0 irig status.
• Resolved a firmware update issue when different SEL-3390S8 cards are installed.

• SEL-3350
• SEL-3390E4
• SEL-3390T
• SEL-3390S8

• Added 3355/3360 support to WMI data providers and SEL Alarm service.
• Added SEL-3390S8 PCIe serial card support.
• Updated IRIG/Time components on all products with new automatic source selection and WMI settings/diagnostics.

• SEL-3350
• SEL-3390E4
• SEL-3390T

• Fixed an incompatibility with the SEL-3390S8 driver that could cause incorrect daylight saving time adjustments.

• SEL-3350

• Changed name to SEL-3300 Driver Bundle.
• Added SysMon installer for the SEL-3350.

• SEL-3350
• SEL-3390E4
• SEL-3390T

• Fixed an issue that could cause PCIe cards to not function if the system has two or more of the same card installed.

• SEL-3350
• SEL-3390E4
• SEL-3390T

• Fixed TCP checksum offload defect that could cause packets with a specific checksum to be discarded.

• SEL-3350
• SEL-3390E4
• SEL-3390T

• Improve downgrade logic when multiple cards are present in a system.
• Add 3390T support.
• Include Broadcom SFP support.

• SEL-3350

• Added IRIG time synchronization support for the SEL-3350.

• SEL-3350
• SEL-3390E4

• Added SEL-3350 support.
• Ethernet Devices: SFP WMI class names changed to SEL_SFPId and SEL_SFPDiag.

• Improve Ethernet throughput performance.
• Add checksum offloading.
• Add WMI provider to provide SFP diagnostics.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for RHEL 8.10 and 9.4.
• Added support for Ubuntu 24.04.
• Added support for SUSE 15.6.
• Discontinued development for RHEL 6 and 7. The SEL 3300 Driver Bundle will include the most recent driver releases for these OSs.
• Updated the SEL MI Contact Input Class pickup and dropout debounce time settings to restrict the minimum setting value to the hardware limits of 4ms at 24V and 2ms at all other voltages.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Updated RHEL 9 package to support the latest kernel.
• Separated RHEL package into individual packages based on RHEL major releases to ensure driver continues to support each version.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for Alma/RHEL 9.3.
• Resolved a compile error for Ubuntu 22.04 with kernel 6.5.0-14-generic.
• Resolved a kernel error that could occur during selmultiuart driver removal.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for Alma/RHEL 9 and Ubuntu 22.04.
• Added support for openSUSE and SUSE Enterprise Linux 15.4 and newer.
• Added /sys/class/leds to control Enabled, Alarm, and Aux LEDs. This replaces accessing them through the General Purpose I/O Class.
• Added /sys/class/power_supply for accessing the status of the power supplies. This replaces accessing this through the General Purpose I/O Class.
• Made the GPIO driver compatible with libgpiod. Access to jumper status, Alarm to OUT101 coupling, and other diagnostics will now go through libgpiod. This replaces the older method of GPIO access described in the General Purpose I/O Class section of the Instruction Manual.
• Dropped 32-bit Operating System support.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Added support for new SEL PCI devices, components, and variants.
• Improved Ethernet SFP behavior on hot-plug and device enable/disable.
• Improved installer to support reinstall on Ubuntu and CentOS.
• Improved IRIG input diagnostics to avoid a potential race condition.
• Resolved a firmware update issue when different SEL-3390S8 cards are installed.
• Resolved a serial driver issue that could cause the serial port to hang.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Addressed a compilation problem that caused installation to fail on RHEL 8.0 and derivatives.

• SEL-3350
• SEL-3390E4
• SEL-3390S8
• SEL-3390T

• Updated IRIG/Time components on all products with new automatic source selection and sysfs settings/diagnostics.
• Added support for PTP hardware time-stamps.
• Added SEL-3390S8 serial card support.
• Added jumbo frame support with a 9000 byte MTU to Ethernet ports on all products.

• No changes

• Made changes to the installation packages to make them compatible with the new SEL Linux repositories. No changes to the driver modules themselves.

• SEL-3350
• SEL-3390E4
• SEL-3390T

• Improve downgrade logic when multiple cards are present in a system.
• Add bit-mode support in MultiUART driver.
• Add 3390T support.
• Add support for Ubuntu 20.04.
• Add support for CentOS/RHEL 8.3.
• Include Broadcom SFP support.

• SEL-3350

• Add IRIG time synchronization support for the SEL-3350.

• SEL-3350
• SEL-3390E4

• Add SEL-3350 support.
• Ethernet Devices: sysfs SFP diagnostic changed to SEL_SFPId and SEL_SFPDiag.

• Improve Ethernet throughput performance.
• Add checksum offloading.
• Add sysfs diagnostic information for connected SFPs.

• Updated the following packages, see package release notes for details:
  • Intel Management Engine: Windows
  • SEL SysMon Software: Windows, SysMon v4

• Updated the following packages, see package release notes for details:
  • Intel Chipset Utility: Windows [7, 8, 8.1, 10, 2008R2, 2012R2, 2016, 2019, 2022] x86-x64
  • Intel Ethernet: Windows [8, 8.1, 10, 2012R2, 2016, 2019, 2022] x86-x64

• Updated the SEL SysMon Software v4 for Windows, see SysMon v4 Readme and Release Notes for details.

• Updated the SEL SysMon Software v4 for Windows, see SysMon Release Notes for details.

• Updated the Intel Management Engine Interface driver to the latest release.
• Added SEL SysMon Software v4 for Windows, see SysMon README.txt files.
• Updated folder names to indicate support for newer Windows versions:
  • Intel Chipset Utility
  • Intel Graphics
  • Intel SATA Controller

• Updated the following packages, see package release notes for details:
  • Intel Ethernet: Windows [8, 8.1, 10, 2012R2, 2016, 2019, 2022] x86-x64

• Updated the following packages, see package release notes for details:
  • Intel Ethernet: Windows [7, 2008R2] x86-x64
  • Intel Ethernet: Windows [8, 8.1, 10, 2012R2, 2016, 2019] x86-x64
  • Intel Graphics: Windows [10, 2016, 2019] x64
  • Intel Management Engine Interface: Windows [10, 2016, 2019] x64
  • Intel SATA Controller: Windows [10, 2016, 2019] x64
• Added Prerequisites to SEL Sysmon Software Windows README.txt.

• Initial tracked release of the 3355-2/3360-2 Drivers and Software bundle.

• [Cybersecurity Enhancement] Updated secure boot databases with the latest Microsoft and SEL keys.
• Added version information to BIOS update error messages.
• [Cybersecurity] Removed BIOS IPv6 support to address the following security notifications: CVE-2023-45229, CVE-2023-45230, CVE-2023-45231, CVE-2023-45232, CVE-2023-45233, CVE-2023-45234, CVE-2023-45235
• [Cybersecurity] BIOS updated for the following security notifications: CVE-2023-5678, CVE-2023-39538, CVE-2023-39539, LogoFAIL

• Added console redirection, with setting located under System Configuration.
• Added an event log entry to indicate when the watchdog has reset the system.
• Added an event log entry to indicate when BIOS settings are modified by the UEFI shell bioscfg command.
• Added automatic cleanup of the UEFI variable store to resolve an issue with Linux filling it with error logs.
• Added a prompt to load default Secure Boot keys when using the Load Setup Defaults function (F9 key or Load Standard Defaults on Save and Exit menu).
• [Cybersecurity] Added a check to prevent loading BIOS settings files when the Administrator Password is set (e.g., using UEFI shell bioscfg command).
• [Cybersecurity] BIOS updated for the following security notifications:
  • AMI Security Advisory SA50133: CVE-2017-5715
  • AMI Security Advisory SA50170: CVE-2021-38578
  • AMI Security Advisory SA50179: CVE-2019-14559, CVE-2019-14584, CVE-2019-14563
  • AMI Security Advisory SA50182: CVE-2023-28005
  • AMI Security Advisory SA50183: CVE-2022-43505
  • AMI Security Advisory SA50184: INTEL-SA-00783: CVE-2022-29871 INTEL-SA-00813: CVE-2022-43505, CVE-2022-27879
  • AMI Security Advisory SA50186: CVE-2022-4304, CVE-2022-4450, CVE-2023-0215, CVE-2023-0286
  • AMI Security Advisory SA50191: CVE-2023-0465
  • AMI Security Advisory SA50193: CVE-2023-0464
  • AMI Security Advisory SA50197: CVE-2022-21894
  • AMI Security Advisory SA50199: INTEL-SA-00752: CVE-2021-33164
  • AMI Security Advisory SA50202: CVE-2023-34470

• [Cybersecurity] BIOS updated for the following security notifications:
  • CVE-2019-14558
  • CVE-2021-28210
  • CVE-2021-28211
  • CVE-2021-30004
  • INTEL-SA-00613: CVE-2022-0004
  • CVE-2022-34301
  • CVE-2022-34302
  • CVE-2022-34303
  • CVE-2022-36372

• [Cybersecurity] BIOS updated for the following security notifications:
  • INTEL-SA-00442: CVE-2020-24489
  • INTEL-SA-00465: CVE-2020-24513
• * Added SEL Boot Check function and associated setting in Boot Features.

• Initial release of the BIOS for the SEL-3350.

• [Cybersecurity] Intel Management Engine (ME) Firmware updated to version 11.8.95.4551, addressing the following security notifications: INTEL-SA-00783: CVE-2022-36392, CVE-2022-29871
• Updated Windows ME Driver package to version 2413.5.67.0.

• [Cybersecurity] Intel Management Engine (ME) Firmware updated to version 11.8.93.4323, addressing the following security notifications:
  • INTEL-SA-00575: CVE-2021-33107
  • CVE-2022-26845, CVE-2022-27497, CVE-2022-29893, CVE-2022-33159
• Updated Windows ME Driver package to version 2227.3.14.0.

• Intel Management Engine (ME) Firmware updated to version 11.8.86.3909, addressing the following security notifications:
  • INTEL-SA-00459: CVE-2020-8703, CVE-2020-24507
• Updated Windows ME Driver package to current release.

• Intel Management Engine (ME) Firmware updated to version 11.8.82.3838, addressing the following security notifications:
  • INTEL-SA-00295: CVE-2020-0531, CVE-2020-0532, CVE-2020-0533, CVE-2020-0535, CVE-2020-0536, CVE-2020-0537, CVE-2020-0538, CVE-2020-0539, CVE-2020-0540, CVE-2020-0545, CVE-2020-0594, CVE-2020-0595, CVE-2020-0596, CVE-2020-8674
  • INTEL-SA-00391: CVE-2020-8705, CVE-2020-8745, CVE-2020-8746, CVE-2020-8747, CVE-2020-8749, CVE-2020-8751, CVE-2020-8752, CVE-2020-8753, CVE-2020-8754, CVE-2020-8756, CVE-2020-8757, CVE-2020-8760, CVE-2020-12303, CVE-2020-12355, CVE-2020-12356
  • INTEL-SA-00404: CVE-2020-8758
• Updated Windows ME Driver package to current release.

• Intel Management Engine (ME) Firmware updated to address the following security notifications:
  • INTEL-SA-00185: CVE-2018-12185, CVE-2018-12187, CVE-2018-12188, CVE-2018-12189, CVE-2018-12190, CVE-2018-12191, CVE-2018-12192, CVE-2018-12196, CVE-2018-12199, CVE-2018-12208
  • INTEL-SA-00213: CVE-2019-0091, CVE-2019-0092, CVE-2019-0093, CVE-2019-0094, CVE-2019-0096
  • INTEL-SA-00241: CVE-2019-0131, CVE-2019-0165, CVE-2019-0166, CVE-2019-0168, CVE-2019-0169, CVE-2019-11086, CVE-2019-11087, CVE-2019-11088, CVE-2019-11090, CVE-2019-11100, CVE-2019-11101, CVE-2019-11103, CVE-2019-11104, CVE-2019-11105, CVE-2019-11106, CVE-2019-11107, CVE-2019-11108, CVE-2019-11109, CVE-2019-11110, CVE-2019-11131, CVE-2019-11132
• Updated Windows ME Driver package to current release.

• Intel released an ME firmware update for the SEL-3355-2 and SEL-3360-2 computers that addresses the AMT security vulnerabilities documented in:
  • CVE-2018-3628, CVE-2018-3629, CVE-2018-3632, CVE-2018-3627, CVE-2018-3657, CVE-2018-3658, CVE-2018-3616, CVE-2018-3655, CVE-2018-3643
  • Intel-SA-00112 (relates to CVE-2018-3628, CVE-2018-3629, CVE-2018-3632)
  • Intel-SA-00118 (relates to CVE-2018-3627)
  • Intel-SA-00141 (relates to CVE-2018-3657, CVE-2018-3658, CVE-2018-3616)

• Initial Intel ME firmware for the SEL-3355-2 and SEL-3360-2 computers.

• [Cybersecurity Enhancement] Updated secure boot databases with the latest Microsoft and SEL keys.
• Updated ACPI to flag SSDs connected via SATA-to-USB adapters as removable devices to improve compatibility with MS Windows USB security policies.
• Added version information to BIOS update error messages.
• [Cybersecurity] Removed BIOS/UEFI IPv6 support to address the following security notifications: CVE-2023-45229, CVE-2023-45230, CVE-2023-45231, CVE-2023-45232, CVE-2023-45233, CVE-2023-45234, CVE-2023-45235
• [Cybersecurity] BIOS updated for the following security notifications: CVE-2023-39538, CVE-2023-39539, LogoFAIL

• Increased the size of the TPM Attestation Event log to 64 K to resolve an issue that could cause the VMware ESXi installer to fail.
• Added an event log entry to indicate when BIOS settings are modified by the UEFI shell bioscfg command.
• Added an event log entry to indicate when the SEL watchdog has reset the system.
• Added a prompt to load default Secure Boot keys when using the Load Setup Defaults function (F9 key or Load Standard Defaults on Save and Exit menu).
• Corrected SEL-3355-2 USB port names in BIOS Setup under the USB Port Disable Override setting to match the rear-panel USB port labels.
• Corrected SEL-3360E PCIe slot names in SMBIOS to match the rear-panel PCIe slot labels.
• [Cybersecurity] Added a check to prevent loading of BIOS settings files when the Administrator Password is set (e.g., using UEFI shell bioscfg command).
• [Cybersecurity] BIOS updated for the following security notifications:
  • AMI Security Advisory SA50133: CVE-2017-5715
  • AMI Security Advisory SA50170: CVE-2021-38578
  • AMI Security Advisory SA50179: CVE-2019-14559, CVE-2019-14563
  • AMI Security Advisory SA50182: CVE-2023-28005
  • AMI Security Advisory SA50183: CVE-2022-43505
  • AMI Security Advisory SA50197: CVE-2022-21894
  • AMI Security Advisory SA50199: CVE-2021-33164
  • AMI Security Advisory SA50202: CVE-2023-34470
  • AMI Security Advisory SA50205: CVE-2023-39537

• Added support for the Intel TCO watchdog.
• Added "Intel TCO" selection to the Watchdog setting.
• Changed the Watchdog setting default value to "Disarmed".
• BIOS updated for the following security notifications:
  • AMI Security Advisory SA50085: CVE-2022-34301, CVE-2022-34302, CVE-2022-34303
  • AMI Security Advisory SA50088: CVE-2019-14558, CVE-2021-28210, CVE-2021-28211
  • AMI Security Advisory SA50097
  • INTEL-SA-00527: CVE-2021-0114
  • INTEL-SA-00532: CVE-2021-0127
  • INTEL-SA-00562: CVE-2021-0157, CVE-2021-0158
  • AMI Security Advisory SA50110
  • AMI Security Advisory SA50112
  • INTEL-SA-00601: CVE-2021-0154, CVE-2021-0188, CVE-2021-0189, CVE-2021-33123, CVE-2021-33124
  • INTEL-SA-00613: CVE-2022-0004
  • INTEL-SA-00614: CVE-2022-0005
  • INTEL-SA-00617: CVE-2022-21151
  • AMI Security Advisory SA50130: CVE-2021-30004

• Fixed an issue where Redhat/CentOS 8.3 gave a bad RMRR error during boot.
• Added SEL Boot Check function and associated setting in Boot Features.
• Exposed system temperatures in ACPI.
• Added failed/invalid capsule updates to the SMBIOS GPNV log.
• Added failed crisis recovery attempts to the SMBIOS GPNV log.
• BIOS updated for the following security notifications:
  • INTEL-SA-00463: CVE-2020-8670, CVE-2020-8700, CVE-2020-12357, CVE-2020-12358, CVE-2020-12359, CVE-2020-12360, CVE-2020-24486, CVE-2021-0095

• Enabled bus-mastering in PCI/PCIe bridges to improve compatibility with some expansion cards and operating systems.
• BIOS updated for the following security notifications:
  • AMI Security Advisory SA50084: CVE-2020-10255
  • AMI Security Advisory SA50085: CVE-2020-10713
  • INTEL-SA-00320: CVE-2020-0543
  • INTEL-SA-00329: CVE-2020-0548, CVE-2020-0549
  • INTEL-SA-00358: CVE-2020-0587, CVE-2020-0588, CVE-2020-0590, CVE-2020-0591, CVE-2020-0592, CVE-2020-0593
  • INTEL-SA-00360: CVE-2020-0599
  • INTEL-SA-00381: CVE-2020-8696, CVE-2020-8698
  • INTEL-SA-00389: CVE-2020-8695
  • INTEL-SA-00390: CVE-2020-8738, CVE-2020-8739, CVE-2020-8740, CVE-2020-8764

• USB port overcurrent mapping updated to correctly report overcurrent conditions on the rear USB ports.
• BIOS Event Log message improvements.
• UEFI Shell ‘bioscfg’ command error message improvements.
• SMBIOS Table improvements for SATA Ports, PCIe Slots, RAM, and Onboard Devices.
• CPU microcode updated.
• BIOS updated for the following security notifications:
  • CVE-2018-12182
  • INTEL-SA-00233: CVE-2018-12126 (Fallout), CVE-2018-12127, CVE-2018-12130 (ZombieLoad, Rogue In-Flight Data Load/RIDL), CVE-2019-11091
  • INTEL-SA-00220: CVE-2019-0123
  • INTEL-SA-00271: CVE-2019-11139
  • INTEL-SA-00270: CVE-2019-11135
  • INTEL-SA-00254: CVE-2019-0185
  • INTEL-SA-00260: CVE-2019-0154
  • INTEL-SA-00289: CVE-2019-11157
  • AMI-SA-50054 Issue #2 (fix for microcode downgrade attack)

• Updated Secure Boot keys.
• Updated BIOS password complexity requirements.
• When BIOS password is set, you can no longer see read only view of BIOS Setup by entering a blank password.
• Updated CPU microcode.
• Improved Boot Count in Setup to include resets.
• Added updates for the following security notifications:
  • CVE-2018-3640, CVE-2018-3639, CVE-2017-3736, CVE-2018-0739, CVE-2017-5704
  • Intel-SA-00159
  • Intel-SA-00160 (relates to CVE-2017-5704 mentioned above)
• The following security notifications either do not apply to these platforms or were addressed in the initial release but are listed here for reference:
  • CVE-2018-6622, CVE-2018-3652, CVE-2018-9056, Intel-SA-00114, Intel-SA-00129, Intel-SA-00130, Intel-SA-00132, Intel-SA-00151, Intel-SA-00157, Intel-SA-00152, Intel-SA-00158

• Initial Release

Updated devices:

• SEL-3390E4
• SEL-3390T

Change Log:

• Initial release of the SEL-3390 Ethernet Adapter Driver for ESXi 7.0.

Updated devices:

• SEL-3390E4
• SEL-3390T

Change Log:

• Initial release of the SEL-3390 Ethernet Adapter Driver for ESXi 8.0.

• Updated the following packages, see package release notes for details:
  • Intel Chipset Utility: Windows [7, 8, 8.1, 10, 2008R2, 2012R2, 2016, 2019, 2022] x86-x64
  • Intel Ethernet: Windows [8, 8.1, 10, 2012R2, 2016, 2019, 2022] x86-x64

• Updated the following packages, see package release notes for details:
  • Intel Ethernet: Windows [8, 8.1, 10-1607, 2012R2] x86-x64

• Updated the following packages, see package release notes for details:
  • Intel Ethernet: Windows [7, 2008R2] x86-x64
  • Intel Ethernet: Windows [8, 8.1, 10-1607, 2012R2] x86-x64
  • Intel Ethernet: Windows [10-1809, 2016, 2019] x64
  • Intel Graphics: Windows [7, 8, 8.1, 10, 2008R2, 2012R2, 2016, 2019] x86-x64
• Added Prerequisites to SEL Sysmon Software Windows README.txt.

• Initial tracked release of the 3355/3360 Drivers and Software bundle.

• Initial Release
• Intel Chipset driver version 10.1.17.1
• Intel GPIO driver version 30.100.1750.1
• Intel I2C driver version 30.100.1750.1
• Intel TXEI driver version 3.0.0.1115

• Processor microcode updates to address Fallout, ZombieLoad/RIDL, and other security issues. See INTEL-SA-00233, CVE-2018-12126, CVE-2018-12127, CVE-2018-12130, CVE-2019-11091, and CVE-2019-0161 for more details.

• Processor microcode update for Spectre Variants 3a, 4, and L1TF. This addresses Intel SA-00115, CVE-2018-3615, CVE-2018-3620, CVE-2018-3639, CVE-2018-3640, and CVE-2018-3646.

• Processor microcode update for branch target injection mitigation to address CVE-2017-5715 (Spectre variant 2).
• Improved boot times (most notably for Linux based operating systems).
• Changed PCI slot names (as reported by the firmware) to match what is printed on the chassis of the computer.
• Changed text for PCI1 in the BIOS setup to correctly report the label and size of the slot on all platforms.
• Updated the BIOSCFG UEFI shell application to ensure the proper restoration of the default boot order during a reset operation.
• Updated 3360E PCI subform strings.
• Implemented various Phoenix security updates that address SMM exploits and other memory related vulnerabilities (see CVE-2015-0949).
• Made BIOS and EC version number available to SMBIOS so they may be accessed by the operating system.
• Improved TPM availability for use on first boot. TPM In versions 1.4 through 1.6 of the BIOS, the TPM is not usable on the first boot after power up (a reboot is required).
• Prevented the deletion of BIOS users and passwords from the UEFI shell.
• Removed hotkey access to ME Setup to improve device security. To access ME Setup you now have to select Intel AMT Setup from within BIOS Setup.

• Improved link-training on PCI expansion slot 5 for improved compatibility with certain expansion cards.
• Disabled Active State Power Management (ASPM) on all PCIe expansion slots to improve compatibilty with certain expansion cards.
• Changed the internal USB headers to use the integrated XHCI Controller.
• Changed the default setting for VT-d to Enabled in BIOS Setup.
• Removed interrupt 15h video calls to improve compatibility with hypervisors.

• Updated ShellFlash64.efi to version 2.30.0.0.
• Resolved RAID boot issue.

• Changed System Watchdog behavior when set to Disabled: on boot the Alarm will now clear and the Enable LED will turn green.
• Changed Primary Display Selection setting default value to IGD.
• Enabled Intel Display Audio function on DisplayPort and DVI display outputs.
• Enabled Intel Advanced Encryption Standard New Instructions (AES-NI) feature set in the CPU.
• Added Custom Defaults support in BIOS Setup.
• Added UEFI shell command "bioscfg" to import/export BIOS Custom Defaults.
• Added UEFI shell command "bootcfg" to configure boot entries.
• Added UEFI PXE boot support.
• Disabled LVDS display device that interfered with some Linux installations.
• Resolved issue with AMT IDE-Redirect and Reboot to Setup functions.

• Enabled SATA Link Power Management (LPM).

• Changed initial watchdog timeout from 300 seconds to 510 seconds to allow more time for operating system boot tasks.
• Updated Setup Lamp Test Button, Pinhole Button Behavior and System Watchdog help text in BIOS Setup to better describe the settings behavior.
• Disabled SATA Link Power Management (LPM).
• Removed Aggressive Link Power Management (ALPM) option from BIOS Setup and disabled ALPM.
• Disabled Advanced Configuration and Power Interface (ACPI) S3 and S4 sleep states. Windows will no longer support standby and hibernate.
• Updated System Power Policy BIOS Setup option to remove S3/S4 reference.
• Moved HDD0 to top HDD position in BIOS Setup boot priority menu to address RAID boot issue.
• Swapped order of the Network Configuration and Peripheral Configuration menu items under the Advanced submenu.
• Updated BIOS PCI slot expansion names in BIOS Setup from "Slot x" to "PCI x".
• Resolved ESXi 5.5 install hang during UEFI boot.

• Initial release of the BIOS for the SEL-3355.

• Intel released firmware update for the PCH in the SEL-3355 and SEL-3360 that addresses the AMT security vulnerabilities documented in CVE-2017-5711, CVE-2017-5712, CVE-2017-13077, CVE-2017-13078, and CVE-2017-13080.

• Intel released firmware update for the PCH in the SEL-3355 and SEL-3360 that fixes the AMT security vulnerability documented in CVE-2017-5689.

• Intel released firmware update for the PCH in the SEL-3355 and SEL-3360 that disables the use of SSL Version 3 thereby removing the POODLE vulnerability as documented in CVE-2014-3566.

• Initial Intel firmware for the PCH in the SEL-3355 and SEL-3360.